Local HVAC Experts in Brentwood, CA | Fairview

Air conditioning check up.

Air conditioning check up on a Goodman heat pump system.

Replaced an older 3-ton unit with a new American Pride Series HVAC system. The homeowner wanted better efficiency and lower energy bills. Installed the outdoor condenser, indoor air handler, and smart thermostat. System is running smoothly with improved cooling performance.

Installed a ductless mini split for a customer who wanted better climate control in their upstairs bonus room. Mounted the indoor unit, ran refrigerant lines, and connected the system to a dedicated electrical circuit. The space is now comfortable year-round.

A homeowner was dealing with high humidity inside their home, causing discomfort and musty odors. We installed a whole-home dehumidifier integrated with the HVAC system. Humidity levels are now balanced, improving air quality and system efficiency.

Customer had excessive dust and allergy issues. Inspected the ductwork and found heavy dust buildup and minor mold growth. Performed a full duct cleaning and installed a high-efficiency air filter. Airflow and indoor air quality are now much improved.

Customer complained that their AC wasn’t keeping the house cool. Found that the thermostat was misreading temperatures, causing short cycling. Installed a new digital thermostat, calibrated the system, and tested airflow. The home is now maintaining the correct temperature.

Responded to a no-heat call in Brentwood today. The homeowner's gas furnace was not igniting. Upon inspection, I found that the flame sensor was malfunctioning. The flame sensor is a critical safety device in Brentwood that ensures the gas burner shuts off if the flame goes out, preventing a dangerous buildup of gas. In this case, the sensor was not detecting the flame properly, causing the furnace to shut down. I carefully cleaned the flame sensor to remove any soot or debris that might be interfering with its operation. After cleaning, I tested the sensor and confirmed it was functioning correctly. The furnace is now operating safely and reliably, providing heat to the home. Remember, a malfunctioning flame sensor can be a serious safety concern, so regular furnace maintenance is crucial.

In Brentwood, I diagnosed a gas furnace with a no-heat issue. The problem was a faulty igniter. I replaced the old igniter with a new one, ensuring proper placement and connection. Then, I tested the furnace to confirm the new igniter was properly igniting the gas and establishing a stable flame. The furnace is now back up and running, providing reliable heat for the homeowner.

Perform regular pm on furnace in attic , check over all heating components for proper operation and tolerances , verified normal operation

Perform regular pm on furnace in attic , check over all heating components for proper operation and tolerances , verified normal perdition

Perform regular pm on furnace in attic , check over all heating components for proper operation , check gas valve , check pressure switch , check and clean flame sensor , check inducer and blower amps , found bad blower capacitor (recommend replacement) , replaced capacitor for blower motor , change and date filter , cycled heat , verify normal operation at time of service

Perform regular pm on furnace in attic , check over all heating components for proper operation , check gas valve , check pressure switch , check and clean flame sensor , check inducer and blower amps , found bad blower capacitor (recommend replacement) , replaced capacitor for blower motor , change and date filter , cycled heat , verify normal operation at time of service

Fixed issue with furnace recommended a zone board in the future

Found blown out high voltage wires supplying furnace , replaced wiring checked over amperage and cycled unit , verified normal operation

I repaired a York heat pump in Brentwood that wasn’t heating. The issue was a malfunctioning defrost board. I replaced the board, cleaned the air handler, and checked the system’s refrigerant levels. The heat pump is now working efficiently and providing consistent heat.

I completed heater repair on a Honeywell system in Brentwood. The thermostat was not controlling the temperature properly. After recalibrating the thermostat and checking the wiring connections, the system began operating as expected, delivering consistent heat.

Perform regular pm on furnace in garage , check over all heating component for proper operation , check gas valve , check pressure switch , check inducer , check capacitor , check and clean flame sensor , check combustion analysis , change and date filter , told customer about filters for future , verified normal operation

Performed regular pm on furnace in attic , checked over all heating components for proper operation , checked gas valve , checked capacitor , check pressure switches , checked thermostat heating function and verified normal operation

No heat call - found dirty flame sensor and faulty signal from thermostat , cleaned off flame sensor and changed out thermostat , verified normal operation

Perform regular pm on furnace in closet , change and date filter , check over all heating components for proper operation , check gas valve , check pressure switch , check and clean flame sensor , check thermostat heating function , check combustion analysis , verify normal operation

Working in Brentwood, CA this afternoon. Performed regular preventative maintenance on both furnaces in the attic , found bad capacitors and replaced at this visit , checked over all heating components for proper operation and verified normal function

In Brentwood, Ca this morning I performed regular pm on furnace in attic , check over all heating components for proper operation , check gas valve , check pressure switch , check inducer , check and clean flame sensor , check combustion analysis , check thermostat , needs to filter asap and filter grill cleaned , verified normal operation at time of visit , cycled heat , no adjustments or repairs needed at this time.

I completed routine maintenance on a Trane S9X1 gas furnace in Brentwood, CA. I started by inspecting the burners and cleaning the heat exchanger to remove soot buildup. I replaced the old 16x20x1 air filter and lubricated the blower motor bearings. The gas valve was tested and calibrated for proper operation. I also cleaned the flame sensor and ensured the thermostat was functioning correctly. After thorough testing, the furnace was running smoothly and ready for winter.

In Brentwood, CA, I cleaned the air ducts using a Rotobrush BrushBeast machine. The ducts were thoroughly vacuumed, removing debris and allergens. Afterward, I sealed all duct joints with aluminum tape, improving airflow and enhancing the home’s air quality.